木质纤维与水泥共同改良软土的力学性能与微观机制分析

通过压实试验、无侧限抗压强度试验和劈裂试验,分析不同木质纤维含量、水泥含量和固化时间对软土力学性能的影响规律,探讨木质纤维、水泥改良软土的微观机制。结果表明,木质纤维的加入对水泥改良软土的击实特性有显著的影响;木质纤维与水泥可有效改善土体的抗压和劈裂抗拉强度,随着木质纤维含量的增加,改良土的抗压和劈裂抗拉强度呈现出明显的“驼峰”现象,并在木质纤维含量为0.25%时最大;木质纤维与水化产物、软土颗粒形成互锁效应,增大了改良土的摩擦力,同时木质纤维还承担一定的拉伸强度,使改良土的劈裂强度增加。     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

Transient Simulation of Hollow‐Fiber Membrane Filtration with Nonuniform Permeability Distribution

Transient simulation of filtration in hollow‐fiber membranes with nonuniform permeability distribution was conducted. The diversity of permeability distributions caused different initial flux and transmembrane pressure distributions. Manipulating the permeability distribution enables a hollow‐fiber membrane to achieve its maximum volumetric flow rate. During solid‐liquid separation, the inter‐adjustment between flux and cake distributions improved their uniformities simultaneously. The reciprocal of the volumetric flow rate of the membranes all increased linearly with water production. Severely nonuniform permeability distribution caused low water production. The numerical results could be applicable to account for the non‐ideal performance of industrial hollow‐fiber membrane modules.     

Fabrication of NixCo3-xS4 hollow nanosphere as wideband electromagnetic absorber at thin matched thickness

Nowadays, transition metal sulfide (TMS), especially for spinel crystal structure (A_xB_3-xS₄), have been proved to be a promising electromagnetic (EM) absorber if been used to deal with the severe electromagnetic pollution. However, EM performance degradation and absorption layer thickness-decreasing at present remains a big challenge, owning to the poor EM attenuation ability. To overcome this barrier, herein we reported a Ni_xCo_3-xS₄ (x = 0, 0.3, 0.6, 1.0) absorber with hollow sphere structure to realize a good EM performance with a thinner matched thickness (<1.5 mm). The average sizes of these Ni_xCo_3-xS₄ distributed in 450–550 nm. The dielectric loss ability (ε'') can be boosted by tuning the molar ratio of Ni/Co, which attributes to EM performance. Additionally, hollow structure would lead to the electromagnetic multi-reflection, also benefited to EM performance. The results demonstrated that the maximum qualified absorption bandwidth (f_E) of 3.8 GHz can be achieved for the Ni_0·3Co_2·7S₄ sample when specimen thickness only equals to 1.3 mm.     

Verification of unified effective stress theory based on the effect of moisture on mechanical properties of fiber reinforced unsaturated soil

The unified effective stress theory based on suction stress (SSCC theory) enables the characterization of soils under both saturated and unsaturated conditions with one closed-form relationship. This study provides experimental verification of this theory through the unconfined compressive strength test (UCS) and indirect tensile test strength (ITS) on silty clay soil stabilized with fiber. A series of matric suction, ITS, and UCS tests were conducted to validate the SSCC theory through the representation of the results of ITS and UCS tests in terms of mean total stress (p) versus deviatoric stress (q) and mean effective stress (p`) versus deviatoric stress (q). The results of the validation procedures showed that the SSCC theory is applicable and valid at a range of 6%–16% of water content on the silty clay and the silty clay fiber-reinforced soils. There is a small fluctuation in the increase of ITS and UCS values with increasing fiber content due to randomly oriented distribution of the fiber. The addition of glass fiber does not significantly affect the capacity of water retention of the soil. It improves the condition of the mechanical soil properties at the end of construction more than of the effective stress condition.     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

A comparative study on the effect of carbon-based and ceramic additives on the properties of fiber reinforced polymer matrix composites for high temperature applications

Ablative composites have been in use for thermal protection of space vehicles for decades. Carbon-phenolic composites have proven to perform exceptionally well in these applications. However with development in aerospace industry their performance needs improvement. In this field, different carbon-based and ceramic additives have been introduced into ablative composite systems. This review article gives a comparative analysis of researches done in this field in the recent past. Density, ablative, thermal and mechanical properties of ablative composites with different ultra-high temperature ceramic particles i.e. ZrSi₂, Cenosphere, nano-SiO₂, BN etc. and carbon-based nanoparticles i.e. CNTs, nano-Diamonds, Graphene oxide etc. used as additives, have been compared and discussed. Emphasis is put on carbon-phenolic composite systems although some epoxy matrix systems have also been discussed for comparison.     

Development of low-loss lead-germanate glass for mid-infrared fiber optics: II. preform extrusion and fiber fabrication

For lead-germanate glass fibers, reducing the content of hydroxyl (OH) groups and the formation of metallic Pb species is essential to pave the way for their applications as low-loss mid-IR fiber optics since OH and metallic Pb species cause intense absorption and scattering loss, respectively, in the mid-IR spectral range. The first part of this study reported the optimization of the glass melting procedure to obtain low amount of OH while preventing formation of metallic Pb species in lead-germanate glass. Here, the second part of this study reports the investigation of the process conditions to fabricate low-loss lead-germanate glass fiber through further understanding of the co-effects of glass melting and heat treatment atmospheres on the formation of nano- and micron-scale metallic Pb species in both the as-produced and heat treated lead-germanate glasses. Finally, using this advance in knowledge, we successfully fabricated low-loss lead-germanate glass fibers with no presence of reduced metallic Pb particles by optimizing dehydration agent, glass melting, preform extrusion and fiber drawing conditions. The optimized fabrication conditions reduced the unstructured fiber loss by almost one order to <0.3 dB/m at 1.55 μm.